Search found 1221 matches
- Mon Oct 28, 2013 11:33 am
- Forum: FG085
- Topic: Control FG085 from serial port
- Replies: 15
- Views: 45328
Re: Control FG085 from serial port
300ms is probably too fast. Please see the other post about communication between the two micro-controllers.
Re: Zeroes
You are right. That was not true. Frequency has to be set to 0 to get DC signal.
- Sat Oct 26, 2013 11:52 pm
- Forum: FG085
- Topic: Control FG085 from serial port
- Replies: 15
- Views: 45328
Re: Control FG085 from serial port
Thank you for the video. The shown behavior was correct. Frequency resolution is 1Hz. Amplitude and offset resolution is 0.1V. Any extra digits entered will be truncated.
- Sat Oct 26, 2013 12:42 am
- Forum: FG085
- Topic: Control FG085 from serial port
- Replies: 15
- Views: 45328
Re: Control FG085 from serial port
Thank you for the video. Unfortunately it couldn't be opened within China :( . For the sequence you gave the amplitude should be set to 0.5V and '3', '1' would be dropped because of resolution limitation. I will think about adding a waveform selection command. Ideally all parameters should be able t...
- Thu Oct 24, 2013 12:10 am
- Forum: DSO 062
- Topic: Sending screen error
- Replies: 19
- Views: 51049
Re: Sending screen error
I think the voltages you measured were OK. -7.16 isn't much different from -7.0. And this voltage is the negative power supply of analog circuits. It is not related to test signal output.
For test signal problem can you please post a photo for what you saw?
For test signal problem can you please post a photo for what you saw?
- Sun Oct 20, 2013 11:04 pm
- Forum: jyeLab
- Topic: jyeLab for DSO096
- Replies: 5
- Views: 21264
Re: jyeLab for DSO096
It might take quite a while. I'm sorry we have been pretty busy with other products. jyeLab was developed after 096 so it takes some extra efforts to make 096 work with jyeLab. We want to do it but only when we find a time slot. Could you please let me know which document said 096 was supported by j...
- Sun Oct 20, 2013 9:30 pm
- Forum: DSO 062
- Topic: Sending screen error
- Replies: 19
- Views: 51049
Re: Sending screen error
The messages PC received only indicated the transmission from scope to PC was good but not necessarily the other way was also okay. Now since screen sending didn't work it is better to verify no hardware problem first. One way to do this is to make PC constantly send out some bytes and use a scope (...
- Sun Oct 20, 2013 1:52 pm
- Forum: DSO 062
- Topic: Sending screen error
- Replies: 19
- Views: 51049
Re: Sending screen error
Which software did you use for receiving?
Did you verify that the transfer from PC to 062 is working?
Did you verify that the transfer from PC to 062 is working?
- Fri Oct 18, 2013 8:25 am
- Forum: jyeLab
- Topic: jyeLab for DSO096
- Replies: 5
- Views: 21264
Re: jyeLab for DSO096
I am sorry. I overlooked the title. jyeLab does not support 096 yet. It only supports 094.
- Sun Oct 13, 2013 4:43 am
- Forum: jyeLab
- Topic: jyeLab for DSO096
- Replies: 5
- Views: 21264
Re: jyeLab for DSO096
Please check the following:
1 ) Main firmware version. It should be 113-09401-050 or later.
2 ) Check 094 baudrate from menu. Set it to match that at jyeLab. 094 baudrate is changeable for firmware version -052 or later.
1 ) Main firmware version. It should be 113-09401-050 or later.
2 ) Check 094 baudrate from menu. Set it to match that at jyeLab. 094 baudrate is changeable for firmware version -052 or later.