Search found 18 matches
- Wed May 02, 2018 5:58 pm
- Forum: DSO Shell
- Topic: What is the white 2 pin alternative power connector
- Replies: 1
- Views: 3578
Re: What is the white 2 pin alternative power connector
Hello, yes it's ok !!
- Mon Mar 12, 2018 7:27 pm
- Forum: DSO Shell
- Topic: Integrated battery case
- Replies: 3
- Views: 7585
Re: Integrated battery case
Thanks for the links on your post I bought two rear covers for my 2 Dso's, and just did the upgrade this afternon Everything is perfect and cover is very well adjusted, i prefer to add capacitor (+/- ouptut 9v) and diode as indicated on the output + 9v. (it was indicated on the schema) I put in them...
- Mon Jan 01, 2018 5:44 pm
- Forum: DSO Shell
- Topic: New v111 now in Firmwares. Another activation key?
- Replies: 7
- Views: 8945
Re: New v111 now in Firmwares. Another activation key?
Hello
2 DSO updated to 111 firmware with no problem, they were pre actived on last 110 firmware, so no need to reactive them
rgds Eric.
2 DSO updated to 111 firmware with no problem, they were pre actived on last 110 firmware, so no need to reactive them
rgds Eric.
- Wed Aug 23, 2017 6:58 pm
- Forum: DSO Shell
- Topic: Positive voltages at V- and AV-
- Replies: 15
- Views: 16262
Re: Positive voltages at V- and AV-
No matter ! that's the job !!!
Like Italians say...10 times you measure...1 time you cut ! lol
Like Italians say...10 times you measure...1 time you cut ! lol
- Tue Aug 22, 2017 9:15 pm
- Forum: DSO Shell
- Topic: Positive voltages at V- and AV-
- Replies: 15
- Views: 16262
Re: Positive voltages at V- and AV-
Eric, Thanks for your help. I found that C13 is shorted out. What value capacitor should I use and how do I remove and replace a surface-mounted cap? please note Corrected version for my post on 23/08/2017 Hello Ok your board is new one, so here C13 is SMD, as i could see on your (poor quality ;-) ...
- Mon Aug 21, 2017 9:43 pm
- Forum: DSO Shell
- Topic: Positive voltages at V- and AV-
- Replies: 15
- Views: 16262
Re: Positive voltages at V- and AV-
Power supply is < 10 volts, ok? Take a look for a bad solder on jack power J7 too (one of mine was bad and there were troubles on some voltages on main board) perhaps it could send bad voltage too on analogic... SWITCH on GND position to check reference voltages So finaly as indicated in the FAQ for...
- Sun Aug 20, 2017 7:10 pm
- Forum: DSO Shell
- Topic: Positive voltages at V- and AV-
- Replies: 15
- Views: 16262
Re: Positive voltages at V- and AV-
Hello
Yes the good side for the caps
regards Eric.
Yes the good side for the caps
regards Eric.
- Fri Aug 18, 2017 7:56 am
- Forum: DSO Shell
- Topic: Firmware update: help request.
- Replies: 12
- Views: 14283
Re: Firmware update: help request.
no you can upgrade to the last firmware, directly to the 062, there are minors bugs but it is ok for the principal use
- Fri Aug 18, 2017 7:47 am
- Forum: DSO Shell
- Topic: Firmware update: help request.
- Replies: 12
- Views: 14283
Re: Firmware update: help request.
Hello juste to be sure... perhaps a bad download, please delete the hex firmware downloaded, and then download it another time Then try a fresh new upgrade then select options "optimise" and "verify" when selecting the hex file from the prog to do the upgrade cause you had contra...
- Fri Aug 18, 2017 4:34 am
- Forum: DSO Shell
- Topic: Fried analog board
- Replies: 9
- Views: 9868
Re: Fried analog board
@ Jye1
Thanks for your advice, i will take a look at that on next opening !
regards Eric.
Thanks for your advice, i will take a look at that on next opening !
regards Eric.