Hi there,
I would like tu update the firmware of my FG085 but it seems that this link is no longer valid:
http://extremeelectronics.co.in/softwar ... beta-test/
Where can I download eXtreme Burner?
Thanks.
Search found 16 matches
- Sun Mar 29, 2020 10:57 pm
- Forum: FG085
- Topic: Help:eXtreme Burner not available
- Replies: 0
- Views: 25464
- Fri Aug 18, 2017 10:46 am
- Forum: DSO Shell
- Topic: Firmware update: help request.
- Replies: 12
- Views: 14341
Re: Firmware update: help request.
No success. I must find a "real" PC, as now I'm working with an emulator (Paralles MacOSX).
- Fri Aug 18, 2017 7:53 am
- Forum: DSO Shell
- Topic: Firmware update: help request.
- Replies: 12
- Views: 14341
Re: Firmware update: help request.
Ok, thanks.
I have a doubt: do I have to perform an incremental update 055->060->061->062?
Now I'm trying to update form 055 to 062.
I have a doubt: do I have to perform an incremental update 055->060->061->062?
Now I'm trying to update form 055 to 062.
- Fri Aug 18, 2017 5:53 am
- Forum: DSO Shell
- Topic: Firmware update: help request.
- Replies: 12
- Views: 14341
Re: Firmware update: help request.
Hi Jye1,
You can see my target selection in the jpeg at the beginning of this thread. It's the same setting found in the firmware update instructions.
Any other ideas?
Best regards
You can see my target selection in the jpeg at the beginning of this thread. It's the same setting found in the firmware update instructions.
Any other ideas?
Best regards
- Thu Aug 17, 2017 3:40 am
- Forum: DSO Shell
- Topic: Fried analog board
- Replies: 9
- Views: 9895
Re: Fried analog board
Thank you very much for your answer.
Could you please look at this post http://www.jyetech.com/forum/viewtopic.php?f=19&t=1250?
I need assistance for another problem.
Best regards,
Could you please look at this post http://www.jyetech.com/forum/viewtopic.php?f=19&t=1250?
I need assistance for another problem.
Best regards,
- Wed Aug 16, 2017 9:31 pm
- Forum: DSO Shell
- Topic: Firmware update: help request.
- Replies: 12
- Views: 14341
Re: Firmware update: help request.
I have removed the protection too. And I can confirm that the warning message is now disappeared.
Basically we are in the same condition, the difference is that I cannot upload completely the .hex file to my DSO.
Best regards,
Basically we are in the same condition, the difference is that I cannot upload completely the .hex file to my DSO.
Best regards,
- Wed Aug 16, 2017 4:49 pm
- Forum: DSO Shell
- Topic: Firmware update: help request.
- Replies: 12
- Views: 14341
Re: Firmware update: help request.
Yes, but I read somewhere in the FAQ that I can ignore it and go to the next page.
And that's what I did.
And that's what I did.
- Wed Aug 16, 2017 3:20 pm
- Forum: DSO Shell
- Topic: Firmware update: help request.
- Replies: 12
- Views: 14341
Firmware update: help request.
I'm trying to update the firmware of my DSO but I'm facing some problems: by mistake I did connect my DSO to the JYE119 Uart-USB Converter with tx->tx and rx->rx instead of tx->rx and rx->tx. Surprisingly this is the only configuration where I can reach my unit (COM 3) in the Flash Bootloader Demons...
- Wed Aug 16, 2017 3:09 pm
- Forum: DSO Shell
- Topic: Fried analog board
- Replies: 9
- Views: 9895
Re: Fried analog board
Hi TonyW,
I did exactly the same: bridged the burnt trace.
My DSO is back at work but I have a lot of doubt about it.
I did exactly the same: bridged the burnt trace.
My DSO is back at work but I have a lot of doubt about it.
- Wed Aug 16, 2017 8:52 am
- Forum: DSO Shell
- Topic: Fried analog board
- Replies: 9
- Views: 9895
Fried analog board
Hi, yesterday I had used my DSO Shell to perform a measurement of a PSU whose output is 18.5 V DC As soon as I have turned on the DSO I felt a kind of "burned smell" while the oscilloscope was not returning a valid output. I disassembled my DSO and found that there is a burned trace on the...