Search found 26 matches
- Tue Aug 01, 2017 11:25 am
- Forum: DSO Shell
- Topic: Scope switches to GND when touching the case -> J3
- Replies: 8
- Views: 8781
Re: Scope switches to GND when touching the case -> J3
Just in case anyone has the same problem: To prevent J3 from touching the digital board, I put some kapton tape on it in the zone where it could make contact (any plastic isolating tape would do the job). That was also my first attempt. However the problem was that there is a huge variation in buil...
- Tue Aug 01, 2017 8:06 am
- Forum: DSO Shell
- Topic: Scope switches to GND when touching the case -> J3
- Replies: 8
- Views: 8781
Re: Scope switches to GND when touching the case -> J3
Sorry for the late response. The Device died after I removed J3. Replaced the Diode which died, but didnt help. However the reason I post this is because I saw the new Revision Boards and change notes. As I see you removed the J3 connector completely that was making trouble for me along with trimmer...
- Thu May 11, 2017 11:27 am
- Forum: DSO Shell
- Topic: D2 Diode Replacement
- Replies: 7
- Views: 8847
Re: D2 Diode Replacement
Alright the marking was misleading then.
I got BZX384-C3V6 marked as T7.
http://www.mouser.com/ds/2/302/BZX384_SERIES-840957.pdf
Just checked voltage and its the wrong one. Oh well.
I ordered two Diodes. Will report back.
I got BZX384-C3V6 marked as T7.
http://www.mouser.com/ds/2/302/BZX384_SERIES-840957.pdf
Just checked voltage and its the wrong one. Oh well.
I ordered two Diodes. Will report back.
- Wed May 10, 2017 8:48 am
- Forum: DSO Shell
- Topic: D2 Diode Replacement
- Replies: 7
- Views: 8847
Re: D2 Diode Replacement
Does yours also say T7 ? Need magnifier to see it
- Tue May 09, 2017 10:38 am
- Forum: DSO Shell
- Topic: D2 Diode Replacement
- Replies: 7
- Views: 8847
Re: D2 Diode Replacement
Yeah I know. But I was asking the SMD package that was used.
Is it DO-214AC, also known as SMA or SOD123? Or something else?
Is it DO-214AC, also known as SMA or SOD123? Or something else?
- Tue May 09, 2017 10:37 am
- Forum: DSO Shell
- Topic: Request for software change II
- Replies: 13
- Views: 15225
Re: Request for software change II
Saw this too on the frontpage. Nice job!jye1 wrote:Source codes released. Please see https://github.com/JYEtech/DSO-Shell-op ... e-version- .
- Mon May 08, 2017 4:18 pm
- Forum: DSO Shell
- Topic: D2 Diode Replacement
- Replies: 7
- Views: 8847
D2 Diode Replacement
Hi,
What is the form factor of the D2 Diode? SOD123 or something else?
Looking for a replacement.
What is the form factor of the D2 Diode? SOD123 or something else?
Looking for a replacement.
- Tue Apr 18, 2017 10:44 am
- Forum: DSO Shell
- Topic: Users Manual v5
- Replies: 2
- Views: 4185
Re: Users Manual v5
Good to see an improvement there. It was also annoying for me.
- Mon Apr 17, 2017 8:32 am
- Forum: DSO Shell
- Topic: Scope switches to GND when touching the case -> J3
- Replies: 8
- Views: 8781
Re: Scope switches to GND when touching the case -> J3
already did that.
What I mean is that the test signal is nervous. it jumps left and right. not up and down.
What I mean is that the test signal is nervous. it jumps left and right. not up and down.
- Sun Apr 16, 2017 2:27 pm
- Forum: DSO Shell
- Topic: Scope switches to GND when touching the case -> J3
- Replies: 8
- Views: 8781
Re: Scope switches to GND when touching the case -> J3
desoldering was a little mess.
The testsignal is not constant it moves right or left . Anyone any ideas what might have caused this?
The testsignal is not constant it moves right or left . Anyone any ideas what might have caused this?